EN Li
EN Rack-mount setup The series can be installed in 19 inches racks. Both the UPS and external battery enclosure need 2U of valuable rack space.
EN 3. Slide in the UPS into the rack rail and lock it in the rack enclosure. 4. Tighten the screw, and the load ca
EN 3.4 EBM Installation (Optional) Connecting the EBM in Tower form: 1. Slide down the UPS and EBM vertically and place two UPS stands with t
EN 4. Take off the front panel, and connect the battery terminal (A) from UPS to EBM terminal (B) shown as below. Users need to remove the small ga
EN 2. Connect the earth line from UPS (port A ) to EBM (port B ) 3. Take off the LCD box, and unscrew the internal screws.
EN 4. Take off the front panel, and connect the battery terminal (A) from UPS to EBM terminal (B) shown as below. Users need to remove the small ga
EN Connecting multiple EBMs in Tower form 1. Connect Earth line between UPS and the first EBM, and then connect Earth Line between the first EBM and
EN Connecting the Multiple EBMs in rack form 1. Connect Earth line between UPS and the first EBM, and then connect Earth Line between the first EBM
EN 3.5 UPS Initial Startup To start up the UPS: 1. Verify that the internal batteries are connected. If optional EBMs are installed, verify that t
EN 4. Operation 4.1 Display Panel The UPS has a four-button graphical LCD with dual color backlight. Standard back-light is used to light up t
EN IMPORTANT SAFETY INST
EN The following table describes the functions of the LCD control buttons. Table2. Description of control button Control Button Switch Functio
EN LCD display functions: The following table describes the functions of the LCD display. Table3. Description of LCD display function No. Des
EN UPS Status Display String Description: The following table shows the description of the LCD display string: Table4. UPS Status Display S
EN 4.2 Operating Mode Normal range mode: Under Input mode the UPS accepts AC input voltage range for +/-20%. Generator mode: Under generat
EN 6. Exit Settings mode: Press and hold the Enter button for 3 seconds or button for 0.5 second to exit setting mode.
EN 5. Communication Port 5.1 RS-232 and USB Communication Ports To establish communication between the UPS and a computer, connect your computer
EN Caution: The EPO must not be connected to any utility connected circuits. Reinforced insulation to the utility is required. The EP
EN 6. UPS Maintenance 6.1 UPS and Battery Care For the best preventive maintenance, keep the area around the UPS clean and dust-free. If the atmo
EN Do not dispose of battery in a fire. Batteries may explode when exposed to flame. Proper disposal of batteries is required. Refer to your l
EN 4. Remove the right inner battery bracket. 5. Pull the battery pack out onto flat area. 6. Install new battery pack in
EN • Remove watches, ri
EN 6.5 Testing New Batteries For a battery test, please check: The batteries must be fully charged. The UPS must be in Normal mode with no ac
EN 7. Specification 7.1 Specification Table7. Electrical Specification Model 1000VA 1500VA 2000VA 3000VA Capacity Watt 900W 1350W 1800W 2
EN Table8. Indicators and Audible alarm Indicator AC Mode NORM---normal mode Backup Mode Show “bATT” and sounding every 4 seconds Load/Battery Le
EN 7.2 Rear Panels The UPS rear panel description table and pictures are shown as below: 876512 431NETWORK/TELEPHONE PROTECTIONINPUT 220-24 0V~I
EN 2000VA Standard model rear panel 2000VA Super charger model rear panel 3000VA Standard & Supper charger
EN The EBM rear panel description table and picture are shown as below: 11 36V &72V EBM rear panel No. Function(36V &
EN 8. Trouble Shooting 8.1 Audible Alarm Trouble Shooting Indication Cause Solution Sounding every 4 seconds The UPS is on battery mode Check the i
EN 9. Software Installation WinPower is UPS monitoring software, featuring user-friendly interface to monitor and control your UPS. This unique s
EN CONTENTS 1. Introduct
EN 1. Introduction Thi
EN 2. Circuit Configuration and Commonly used Symbols Following figure shows the basic internal circuit configuration of the UPS 2.1
EN 3. Installation 3.1 Inspection of Unit Inspect the UPS upon receiving. If the UPS is apparently damaged during the shipment, please keep the bo
EN Use the following procedure to install UPS in UPS stands. 1. Slide down the UPS vertically and put two UPS stands at the end of the tower.
EN 3. Pull out the LCD box and rotate it in a clockwise direction to 90 degree and then push it back in the front panel.
Comments to this Manuals